This week I am creating a custom queen sized solid Hickory platform bed for an amazing couple here in Austin. The pic above is the rough cutout pieces for the headboard and the footboard. It is all made from skip planed 6/4" solid hickory.

Today I finished the wood work portion of the bed. I used a 4 1/2" angle grinder with a flap disc to finish carving out the headboard shape. The slats are 1x4 Poplar with a double 1x4 Hickory drop beam in the center for support. I will stain and finish tomorrow. Come back for a completed pic.

Finished the platform bed today. Took right at 3 days. The headboard is made from random width rough sawn 6/4" Hickory and has custom iron and square nail detail work on the sides. This one was fun!

Today I completed this custom Alder and Antique Barnwood media center for an amazing family here in Austin TX. The pulls are custom hand forged steel as well. This picture is the lower unit. Come back next week for the installed picture which will show an upper unit as well. The upper cabinet features custom sliding "barn doors". The rail system on that part was challenging!

Today I built this antique barn wood headboard. The colors are all natural with a water based non-VOC clear. My client wanted a chevron pattern. This one is for a queen sized bed and is 6' tall!

Yesterday I built this antique barn wood headboard. The colors are all natural. Only time and God can create something this beautiful. My client wanted a chevron pattern. This one is a 67/33 chevron. It is for a full size bed.

Today


I built this custom antique barn wood barn door. The backside is custom tongue and groove poplar 1x8. The pull hardware is custom forged from 1/2 round steel. The finish on the barn wood side is clear over what God has done for the past 80 years and the back is painted white to match the client's trim.

Today I picked up the lumber at Fine Lumber and Plywood in Austin.

I made the the top ring of the table out of 1x8 Hickory cut at a 22.5 deg angle on each end. The outside (long dimension) on each side is 19-7/8". That makes a poker table that is 48" across. I started the day making it fit in a 48" diameter circle, but quickly learned that the table was going to be too small if I did that.

The cupholder holes are 3 1/2" diameter holes cut with a hole saw. The chip holder cutout is 4 1/2" x 9 1/8" and will be large enough to hold 5 rows of poker chips.

I biscuit jointed the mitered ends with 2 #20 biscuits per joint and glued the joints with gorilla wood glue.

Tomorrow, I will build up the edges to
2-1/4" thick, create the playing field cutouts and start the pedestal as well.

Today I built the playing surface and the base of the table top out of 3/4" Hickory plywood. I cut strips of 3/4" solid hickory and biscuited them to the edges of the top ring to create a hick top look. I also built the pedestal out of solid 6/4" Hickory cut on a 22.5 deg angle.

Tomorrow I will attach the pedestal to the top and create the "feet" for the pedestal out of 8/4" Hickory. This one is getting close. About 3 more days.

Today I finished the woodwork on the top. I made a mounting ring to attach the pedestal and built the the trim skirt around the bottom of the top. I also created feet out of 8/4" Hickory laminated together to make it 4" thick. The pedestal has been biscuited, glued and screwed together with Kreg pocket screws. I also cut out the brindle hide to fit the playing surface. That's enough for today. It's Good Friday!! Easter is coming!! He is Risen!!

Finished the poker table today. I glued batting to the sub top then stretched the brindle hide over that. Finally, finished the hickory with 3 coats of teak oil. I think this one turned out fantastic!

I am building a custom distressed dining room table today. I started this project with 2x6 SYP studs. In order to turn framing lumber into a piece of furniture there is a great deal of mill work that needs to be done first. I ripped each 2x6 down to 5" then jointed the edges so they were flat and had square edges. Only then was I able to put the table top together.

This is one should only take another day or so. Should be beautiful!

I think this one turned out beautifully, but the client was not happy. I am pulling this one back and am going to rework the finish for them. The customer is always right! Stay tuned for the updated photo.

After many hours of stripping and sanding, this is the new finished distressed pine dining table.  The finish is a new product that I had never used before called "Weathered Wood".  It actually reacts with the tannins in the wood to produce a weathered look.  The surface is then treated with an oil for protection. 

​Today -

I am building a custom vanity top for another amazing close friend and former Indianapolis Colt!

This one is made completely out of recycled pallet wood and will have a custom hammered copper front lip.  The entire top will be set in 2 gallons of clear epoxy and will house double copper and glass vessel sinks.

Check out my website for more!

jonarcherdesigns.com

I would absolutely LOVE to help you create that one of a kind impossible to find custom piece that will set your space apart!

Today

Finished the pallet wood double vanity with copper and glass vessel sinks and oil rubbed bronze fixtures. This one includes a custom hammered copper front edge.

The photo above is the inspiration piece. My client loves this piece, but has some very specific size restrictions. In addition to the size restrictions, they want to change the finished just a bit. Let's see how I do.

Today I am building a custom kitchen hutch for an amazing couple! I made the cabinet boxes out of 3/4" maple plywood. The top of the cabinets is 2"thick solid Hickory that I milled down from rough sawn 8/4 Hickory.

Completed custom kitchen hutch. From a conceptual sketch on a legal pad. This piece has 2" thick distressed Hickory tops finished with water based walnut wiping stain and polyacrylic. It has hand made poplar cathedral doors. The cabinet and doors are finished with an "antiqued" chalked paint.